Table of Contents
Linear and Rotation Stages
This page describes the motorized positioning stages available at the BTF, including their main technical specifications, control hardware, and operating procedures.
Linear Stages
Overview
The BTF is equipped with two PI L-836.531212D motorized linear stages.
The L-836 is a compact, stackable linear stage driven by a two-phase stepper motor and a precision ball screw. The L-836.531212D provides 100 mm of travel and is equipped with an incremental linear encoder for position feedback.
Each stage is controlled by a dedicated PI C-663.12 Mercury Step single-axis stepper motor controller.
The main components of the system are therefore:
- 2 × PI L-836.531212D linear stages
- 2 × PI C-663.12 Mercury Step controllers
The detailed connection between the stages and their controllers, as well as the control software used at the BTF, is described in the Control and Operation section.
L-836.531212D Linear Stages
The L-836.531212D linear stage.
The L-836.531212D is a motorized linear stage with a 100 mm travel range and an integrated incremental linear encoder. The stage uses a two-phase stepper motor and a ball screw drive.
Technical specifications
| Parameter | Specification |
|---|---|
| Manufacturer | Physik Instrumente (PI) |
| Model | L-836.531212D |
| Number of units at BTF | 2 |
| Active axis | X |
| Travel range | 100 mm |
| Maximum velocity | 80 mm/s |
| Maximum acceleration, unloaded | 4 m/s² |
| Load capacity | 150 N |
| Minimum incremental motion | 0.24 µm |
| Positioning accuracy, uncalibrated | ±25 µm |
| Bidirectional repeatability | 0.8 µm |
| Drive type | 2-phase stepper motor |
| Drive screw | Ball screw |
| Drive screw pitch | 2 mm |
| Guide | Recirculating ball bearing guide |
| Integrated sensor | Incremental linear encoder |
| Encoder signal | A/B quadrature, RS-422 |
| Encoder signal period | 80 µm |
| Encoder resolution | 80 nm |
| Reference switch | Hall effect |
| Limit switches | Hall effect, normally closed, 5 V, NPN |
| Operating voltage | 24–48 V |
| Nominal motor current | 1.5 A RMS |
| Maximum power consumption | 8 W |
| Motor resolution | 200 full steps/revolution |
| Drive force | 75 N (typical) |
| Operating temperature | 5–40 °C |
| Connector | HD D-sub 26, male |
| Overall mass | 910 g |
The L-836.531212D has a maximum permissible push force of 150 N in the Z direction. The maximum permissible torques are 15 Nm around the X and Y axes and 10 Nm around the Z axis.
The stage does not include an electromagnetic holding brake.
The L-836.531212D is specified by PI for use with the C-663 controller family, among other compatible controllers. PI L-836 product page
C-663.12 Mercury Step Controllers
The C-663.12 Mercury Step controller.
The C-663.12 Mercury Step is a compact, single-axis controller for two-phase stepper motors. It supports both open-loop and closed-loop operation and provides position feedback through an external encoder.
At the BTF, two C-663.12 controllers are used, one for each L-836.531212D linear stage.
Technical specifications
| Parameter | Specification |
|---|---|
| Manufacturer | Physik Instrumente (PI) |
| Model | C-663.12 Mercury Step |
| Number of units at BTF | 2 |
| Number of controlled axes | 1 |
| Supported motor type | 2-phase stepper motor |
| Operating voltage | 24–48 V DC |
| Maximum output power | 60 W |
| Average output power | 48 W |
| Maximum current per motor phase | 2.5 A |
| Microstep resolution | 1/2048 full step |
| Control mode | Open-loop and closed-loop |
| Servo cycle time | 50 µs |
| Motion profile | Trapezoidal velocity profile |
| Encoder input | A/B quadrature, TTL, RS-422 |
| Limit switch inputs | 2 × TTL, programmable |
| Reference switch input | 1 × TTL, programmable |
| Index switch input | 1 × RS-422 |
| Communication interfaces | USB, RS-232 |
| Motor/sensor connection | HD D-sub 26, female |
| Controller network | Up to 16 units via USB |
| I/O | 4 analog/digital inputs, 4 digital outputs |
| Command set | PI General Command Set (GCS) |
| User software | PIMikroMove |
| Operating temperature | 5–50 °C |
| Dimensions | 130 × 76 × 40 mm |
| Mass | 0.48 kg |
The controller supports point-to-point motion, startup macros and data recording. It also provides functions for encoder-based closed-loop operation, limit and reference switches, and position-error monitoring.
The C-663.12 provides USB and RS-232 interfaces for command and control. Multiple controllers can be connected in a daisy-chain network.
Rotation Stages
Overview
The BTF is equipped with one PI M-062.2S precision rotation stage, used for the angular positioning of experimental equipment.
The stage is operated by a dedicated PI C-663.11 Mercury Step controller.
PI M-062.2S Precision Rotation Stage
The M-062.2S rotation stage.
The M-062.2S is a motorized precision rotation stage manufactured by Physik Instrumente (PI). It uses a two-phase stepper motor and a worm-gear drive and provides continuous rotation over more than 360°.
Technical specifications
| Parameter | Value |
|---|---|
| Active axis | Rotation |
| Rotation range | > 360° |
| Platform diameter | 120 mm |
| Minimum incremental motion | 18 µrad |
| Backlash | 240 µrad |
| Unidirectional repeatability | 60 µrad |
| Maximum velocity | 16°/s |
| Recommended maximum velocity for continuous operation | 8°/s |
| Maximum axial load | ±650 N |
| Maximum torque θX, θY | ±7 Nm |
| Maximum torque θZ | ±8 Nm |
| Drive | Worm gear |
| Worm gear ratio | 110:1 |
| Motor type | 2-phase stepper motor |
| Full steps | 400 steps/motor revolution |
| Maximum phase current, bipolar | 850 mA |
| Reference point switch | Hall-effect sensor |
The M-062.2S is an open-loop positioning stage and does not use a position encoder.
PI C-663.11 Mercury Step Controller
The C-663.11 Mercury Step controller.
The C-663.11 Mercury Step is a single-axis controller for two-phase stepper motors. It provides microstepping motion control and supports both RS-232 and USB communication.
At the BTF, the C-663.11 is connected to the M-062.2S rotation stage and is currently operated through its RS-232 interface.
Technical specifications
| Parameter | Value |
|---|---|
| Number of axes | 1 |
| Drive type | 2-phase stepper motor |
| Microstep resolution | 1/16 full step |
| Trajectory profile | Trapezoidal, point-to-point |
| Limit switch inputs | 2 × TTL, programmable |
| Reference switch input | 1 × TTL, programmable |
| Motor brake output | 1 × TTL, programmable |
| Operating voltage | 15–30 V |
| Maximum current per motor phase | 1000 mA |
| Communication interfaces | USB, RS-232 |
| Motor connector | D-sub 15 (female) |
| Command set | PI General Command Set (GCS) |
| User software | PI MikroMove |
| Operating temperature | 5–50 °C |
| Dimensions | 130 × 76 × 40 mm |
| Mass | 0.3 kg |
Temporary Control Configuration
During commissioning and laboratory tests, the PI controllers are connected to the BTF network through a MOXA NPort 5450 serial device server (NPORT411, IP address 192.168.190.57).
Each controller is connected to a dedicated RS-232 port of the NPort. The ports are configured with the serial communication parameters required by the PI controllers.
| MOXA port | Alias | Controller | Stage | Baud rate | Serial configuration |
|---|---|---|---|---|---|
| 1 | l836_426004915 | PI C-663.12 | S/N 426004915 | 9600 | 8N1, no flow control |
| 2 | l836_426004916 | PI C-663.12 | S/N 426004916 | 9600 | 8N1, no flow control |
| 3 | rM062.2S | PI C-663.11 | PI M-062.2S | 9600 | 8N1, no flow control |
The NPort is currently configured in Real COM Mode. On the laboratory PC, each NPort serial port is therefore exposed as a virtual COM port and can be accessed directly by PI MikroMove.
| MOXA port | Virtual COM port |
|---|---|
| 1 | COM1 |
| 2 | COM2 |
| 3 | COM3 |
The current configuration is used for commissioning and motion tests and is not intended to represent the final BTF control architecture. The final TCP/IP-based control system will be implemented by the Control System service and documented here when available.




