The DAΦNE Beam Test Facility (BTF) is a particle beam facility located at the INFN Laboratori Nazionali di Frascati (LNF), Italy, and is part of the DAΦNE accelerator complex.
BTF provides electron and positron beams with adjustable energy, intensity, and transverse properties for detector development, characterization, calibration, beam diagnostics, and irradiation studies. The facility supports both INFN research groups and external users from national and international institutions.
One of the main features of BTF is its high operational flexibility, allowing beam parameters to be adjusted according to experimental requirements, including during data taking.
The facility comprises two experimental halls, BTFEH1 and BTFEH2, served by a common beam transport system connected to the DAΦNE LINAC.
The DAΦNE LINAC produces pulsed electron and positron beams, primarily used for injection into the DAΦNE storage rings at a nominal energy of 510 MeV.
A pulsed magnet (DHPTB101) redirects selected LINAC pulses towards the BTF transfer line, where a system of dipoles, quadrupoles, collimators, and diagnostic devices allows the beam properties to be adjusted.
The facility can deliver both primary high-intensity beams and secondary low-intensity beams, down to the single-particle regime.
The main beam characteristics are summarized below:
| Parameter | BTF capabilities |
|---|---|
| Particle type | Electrons and positrons |
| Electron energy | Approximately 25–780 MeV |
| Positron energy | Up to approximately 550 MeV |
| Particle multiplicity | From single particles up to ~1010 particles/s |
| Maximum repetition rate | 49 Hz |
| Typical pulse duration | 10 ns |
| Operating modes | dedicated |
The achievable beam parameters depend on the requested particle type, energy, intensity, operating mode, and experimental hall.
Low-intensity secondary beams are obtained by intercepting the primary LINAC beam with a copper target (TGTTB01), whose thickness can be selected to achieve the required attenuation.
A bending magnet (DHSTB001), together with a system of upstream and downstream horizontal collimators, provides momentum selection and particle multiplicity control.
The selected beam is transported and focused by a series of quadrupole magnets and horizontal and vertical correctors, allowing its transverse properties to be adjusted according to experimental requirements.
The downstream beam transport system allows the beam to be directed towards either of the two experimental halls.
This configuration provides a wide range of beam intensities, from single particles suitable for detector calibration to high-intensity pulses for dedicated experimental applications.
BTF consists of two experimental halls with complementary capabilities. Both are equipped with beam diagnostics and infrastructure supporting detector tests and experimental activities.
BTFEH1 is the original BTF experimental hall and is designed to accommodate a wide range of experimental setups, including large detectors and long-duration experiments.
It can receive both low- and high-intensity electron and positron beams, including direct primary LINAC beams in dedicated operating configurations.
The beam intensity and transverse properties can be adjusted according to the experimental requirements, making BTFEH1 particularly suitable for:
BTFEH2 is the second experimental hall, developed to extend the capabilities of BTF and increase the availability of beam time for experimental users.
It is primarily optimized for low-intensity electron and positron beams, with a maximum particle flux of approximately 10^6 particles/s.
The beam is delivered through a dedicated transfer line branching from the main BTF transport system. Beam energy, multiplicity, and transverse properties can be adjusted to match the requirements of individual experiments.
Both halls share part of the beam transport system. Beam delivery is therefore configured for one experimental hall at a time.
| Feature | BTFEH1 | BTFEH2 |
|---|---|---|
| Main application | High-intensity and long-duration experiments | Low-intensity detector tests and user campaigns |
| Beam species | e-, e+ | e-, e+ |
| Beam intensity | Up to approximately ~1010 particles/s, subject to operating conditions | Up to ~106 particles per second |
| Beam configurations | Primary and secondary beams | Primarily secondary beams |
| Beam energy | Dependent on particle species and operating mode | Dependent on particle species and operating mode |
| Experimental infrastructure | Diagnostics, movable tables and technical services | Diagnostics, movable tables and technical services |
Both experimental halls provide infrastructure and technical services supporting experimental activities.
Depending on the experimental setup and availability, these include:
Dedicated control and working areas are available to experimental teams.
BTF personnel provide scientific and technical assistance throughout the experimental campaign, including beam setup, optimization, monitoring, and troubleshooting.
BTF supports experimental activities on a 24/7 basis during scheduled beam periods.
Beam time is allocated through dedicated calls and scheduling procedures. Experimental proposals are evaluated according to the requested beam conditions, technical feasibility, and facility availability.
Information about beam parameters, user access, beam time applications, and operational procedures is available on the official BTF website.
For further information, please contact:
BTF Team: btf@lists.lnf.infn.it